How do I fix error code 12 on Rinnai?
How do I fix error code 12 on Rinnai?
Rinnai Error Code 12 Troubleshooting
- Check gas is turned on at the gas metre or cylinder.
- Check gas is turned on at the water heater.
- Check there are no obstructions to the flue outlet.
What does 12 mean on Rinnai gas heater?
flame failure
If you’re getting Rinnai error code 12 on your hot water unit, it indicates that a flame failure has occurred on the system. In this instance, your hot water unit has not recognised that there is a flame in the burner box.
How do you clear a Rinnai code?
After flushing water heater, the procedure to reset LC codes: Push the two switches (A and B) on PC Board at the same time for five seconds. Water heater will return to normal operation and LC# count returns to 0. This hard reset procedure is not in owners/installation manual or tech sheet.
How do I fix code 11 on Rinnai?
Rinnai fault code 11 – No ignition. Check to make sure the gas is turned on at the water heater, gas meter or tank. Ensure the igniter is operational. If gas is being supplied to the tankless water heater and the igniter is working, call for an evaluation by a qualified plumber.
What does code 12 mean on a furnace?
The code 12 is normal if the furnace is powered up with a call for heat and the blower will run for 90 seconds before it tries to light.
What does 11 mean on Rinnai?
Rinnai error code 11 is an indication that there is no ignition in, or no gas supply to your hot water system. You can try the following to fix the problem: Check your hot water system for any visible damage or loose parts. Locate your gas supply and ensure it is turned on.
How do I fix noritz Error Code 12?
Error Code 12 Problem: Burner flame loss during operation; flame rod does not detect a flame. Solution: Check for the incoming gas pressure. Remove any obstructions in the venting system. Clean the ignition plug and flame rod.
How do I reset my Rinnai Control R WIFI module?
control•r™ 2.0 – How do I factory reset the module? Press and hold the Connect button on the module until the LED blinks RED and WHITE, and then release then QUICKLY tap 3 times. This will restore the module back to original factory settings.
Why is my Rinnai flashing 11?
Rinnai Gas Heater fault code 11 indicates a no ignition or no gas supply on your gas heater system. A gas supply issue may be present if the flame on the gas heater pilot drops in pressure, of if your gas heater does not work then there is no gas supply present.
What is the meaning of Code 12?
Code 10 Bomb threat. Code 12 Notify news media. Code 20 Officer needs assistance. Code 22 Restricted radio traffic. Code 30 Officer needs HELP – EMERGENCY!
What does error code 12 mean on my Rinnai hot water system?
Error code 12 indicates your Rinnai hot water system has a flame failure or low gas flow. If you encounter error code 12, you can try the following steps to fix the problem: Check gas is turned on at the gas metre or cylinder Check gas is turned on at the water heater
Can you put liquid on top of Rinnai 5 Energysaver?
Rinnai Australia 5 Energysaver® – Operation & Installation Manual SAFETY DO NOT place containers of liquid on top of the heater. Water spillage can cause extensive damage to the appliance and may result in electric shock. A dedicated 240V 10 Amp power point be used with this appliance.
What does error 12 on Rinnai gas heater convector 516tr mean?
Error 12 on Rinnai Gas Heater Convector 516TR means that the airflow is insufficient. The filter needs cleaning. There is a sensor behind the small filter (the filter that has a screw). This sensor may also need cleaning if it is covered in dust.
Does Rinnai have problems with their heaters?
‘Mr Rinnai’ came out again, contacted his Tech contact at Rinnai and he said yes they have had problems with this heater and what it needed was a ‘MOD KIT’ installed. Rinnai said there is no charge and it took ‘Mr Rinnai’ about 2 hours to fix it.
