How much HP can I get out of a 289?
How much HP can I get out of a 289?
If you rev an engine high enough it will make the HP (assuming it’s designed to do so), but it’s far from a good street engine. IMHO, 300-350hp is pretty much the upper limit for a streetable 289.
How can I make my 289 faster?
You can change the intake to a quality dual plane manifold, add headers, increase you cam’s lift and duration, add quality aluminum cylinder heads, increase your compression (beef up the bottom end). You most cost effective way to build a 289 is to not.
How big can you bore and stroke a 289?
Ford Engine Bore and Stroke Chart
| Ford Stock Engine Bore and Stroke Guide | ||
|---|---|---|
| 221 | 3.500 | 2.870 |
| 260 | 3.800 | 2.870 |
| 289 | 4.000 | 2.870 |
| 302 | 4.000 | 3.000 |
Can you stroke a Ford 289?
Registered. Yes, you can.
How can you tell the difference between a 260 and a 289?
The main difference between a 260 and a 289 is the 260 has a 6 inch space between the motor mount bolt holes, while the 289 has a 7 inch space. All 260 engines have a 5-bolt bellhousing bolt pattern. The 1963 and 1964 1/2 289 engines have the same 5-bolt pattern. The 260 has a smaller cylinder bore.
How many liters is a 289?
The 289 cu in (4.7 L) was also introduced in April 1963. Bore was expanded to 4.00 in (101.6 mm), becoming the standard bore for most small block engines. Stroke remained at 2.87 inches.
What should the timing be set at on a Ford 289 engine?
The timing specification for the 289 is 6 degrees before top dead center.
How fast can a 289 go?
Turning to the question asked, a stock size tire, a 2.79 final gear ratio, (assuming a manual tranny with minimal slipage) and 4,500 rpm would get you about 122-125 mph top speed.
What stroke is a 408 Windsor?
4.000
Comparable Engines
| Product: | Current: 408 Ford Long Block | 427 Crate Engine |
|---|---|---|
| Bore/Stroke: | 4.030 x 4.000 | 4.030 x 4.170 |
| Block: | OEM 351W | OEM 351W |
| Crankshaft: | Cast Steel | 4340 Forged Steel |
| Rods: | I-Beam, 5140 Forged Steel | H-Beam, 4340 Forged Steel |
How much horsepower does a 302 Windsor have?
Ford 302 cid V-8 Specs
| Engine: | Ford 302 Windsor V-8 (5.0L) |
|---|---|
| Ignition: | Standard distributor |
| Engine Weight: | ~ 450 lbs |
| Engine Oil Capacity: | 6 qts w/ filter |
| Peak Horsepower: | 130 hp – 205 hp (see table below) |
What engine did the 64 1/2 Mustang have?
289cid
The 64 1/2 convertibles had a 289cid engine, and the hardtops came with the less powerful 260 V-8. Thirty five convertibles were sold to dealerships and 195 hardtops were given out in dealer contests held in April of 1964. Clearly the new Ford Mustang was suddenly everywhere!
How much does a Ford 289 weigh?
The 289 cu in (4.7 L) was also introduced in April 1963. Bore was expanded to 4.00 in (101.6 mm), becoming the standard bore for most small block engines. Stroke remained at 2.87 inches. The 289 weighed 506 lb (230 kg).
What is the HP of a Ford 289?
The Ford 289 engine is a 90-degree V8 OHV cast-iron small block that originally had a horsepower rating of 195 for the two-barrel carburetor , and 210 horsepower for the four-barrel carburetor version.
What is a 289 engine?
Introduced in 1963, the 289 CID, 4.7-liter V8 engine was a small block unit Ford designed to be an entry level V8 for all models in their lineup. With small dimensions, a relatively small weight, and decent power, the 289 engine was an impressive offering for car buyers.
What is a Ford engine?
Ford engines are those used in Ford vehicles and in aftermarket, sports and kit applications. Different engine ranges are used in various global navistar markets.
