Does a Shovelhead have an oil filter?
Does a Shovelhead have an oil filter?
The Shovelhead engine, as produced up to 1981, relied on an in-oil tank filter element to keep debris from entering the engine. Unscrew the oil tank cap from the left side of the motorcycle, located directly below the rider’s seat.
How much oil does a Harley engine take?
Slide the new filter into place and replace the oil filter cap. Fill the oil tank with fresh oil. Using a funnel, fill the oil to the proper level. You should need about three quarts.
What size is a Shovelhead motor?
Shovelheads were twin-cylinder, air-cooled, four-stroke motors. The V was arranged front-to-back. The cylinders were aligned at 45 degrees around the crankshaft. While the bottom half of the Shovelheads were the same, they were made in two sizes: 75 and 80 cubic inches.
When was the last Shovelhead made?
The Shovelhead engine is a motorcycle engine that was produced by Harley-Davidson from 1966 to 1984, built as a successor to the previous Panhead engine.
Where is the oil drain plug on a Harley Softail?
On Softails, the drain plug is found between the rear shocks; Dyna and Touring models have drain plugs under the left side of the engine’s oil pan. Replace the drain plug’s O-ring, then screw it into place after the oil has drained. Tighten the drain plug to 18 foot-pounds with a torque wrench.
How much oil does a Harley 103 primary take?
Changing oil belongs in the service department. I am aware that it takes three quarts of oil. The primary is only supposed to be filled up to the BOTTOM of the clutch spring. Start with one QT and add little by little until the level reaches the bottom of the shiny ring at the bottom of the clutch pack housing.
How much oil does a Softail take?
The Harley service manual says it will take 20-24 oz. On mine it’s closer to 20 oz. You’ll just have to fill until you’ve used a little less than a full quart, check the level and adjust accordingly.
How many miles will a Shovelhead last?
Numerous Harley technicians even stated that without necessary top-end modifications, the motors would often last only between 500 and 5,000 miles.
Why do Shovelheads leak oil?
Common Oil Leaks For The Shovelhead As I noted earlier in the post, any engine at any point in time may develop a leak. A worn engine may leak at the head or valve cover gaskets. The oil pump was another commonplace for them to leak.
How much oil do you put in a Harley Davidson shovelhead?
Recommended Fluids Harley-Davidson recommends 4 quarts of SAE 50 or 60 engine oil in all 1966 through 1984 shovelheads. The transmission uses 1.5 pints of HD transmission lubricant, although many people use 75w90 gear oil mixed 3-to-1 with Lucas oil. Harley-Davidson makes two types of fork oil for shovelheads.
What kind of brake fluid does a Shovelhead use?
Shovelhead models from 1966 to 1975 use Dot 3 brake fluid. Models 1975 and later use Dot 5 brake fluid. The front fork oil capacity varied over the 18 years the shovelhead was in production. Instructions for new front forks include the amount of oil required. Models from 1966 to 1969 use 6.5 oz. of fork oil.
How often should you change the oil in a Shovelhead?
Fluid Maintenance Intervals. The official maintenance recommendation is to change engine oil every 5,000 miles, but changing the oil at 2,500 miles is a good idea for an older shovelhead. The primary lubricant should be changed at 5,000-mile intervals, the transmission oil every 10,000 miles and the the fork oil every 20,000 miles.
What kind of fork oil does a Shovelhead use?
HD Hydra-Glide fork oil is for 1966 to 1969 models. All shovelhead models 1970 and later use HD Type B fork oil. HD Primary Chaincase is used in the primary chaincase. Shovelhead models from 1966 to 1975 use Dot 3 brake fluid.
