Useful tips

How do I fix error code 5b00?

author 0

How do I fix error code 5b00?

How to fix Canon printer error 5b00

  1. Step 1: Unplug the device.
  2. Step 2: Press down and continue to hold the power button of the printer and plug the power cord into the wall socket.
  3. Step 3: Hold the power button until the printer starts resetting itself.
  4. Step 4: Wait for the green power light in the printer to turn off.

How do I fix iP2770 error 5b00?

How to Fix Canon Pixma iP2770 error 5B00

  1. Turn off printer.
  2. Press and hold RESET button.
  3. Press and hold POWER button.
  4. Released RESET button, POWER still pressed.
  5. Press and released RESET button 5 times.
  6. Released POWER button.
  7. When computer detect FOUND NEW HARDWARE, wait about 20 seconds and press CANCEL.

How do I reset my Canon iP2770 continuous ink?

Hold down Resume button and press Power button. Keep holding down Power button and let Resume button go. Then Press Resume button 5 times then let BOTH buttons go. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

How do you fix a full ink absorber?

Press and hold the “Power” button and reconnect the power cord. When the printer comes on, release the button. Wait five seconds and push the “Power” button again. This resets the printer’s internal memory and overrides the “Ink Absorber Full” error code.

How do you clean an ink absorber?

  1. Take a bowl with warm water and add some soapy material.
  2. Open the ink cartridge compartment.
  3. wait for ink cartridges and disconnect the printers power cord.
  4. Look balck rubber frame under the ink cartridge.
  5. pull the rubber frame out of the printer and remove ink absorber pads.
  6. clean the pads in the bowl.

How do I fix my Canon IP2770 printer not responding?

Turn off the printer while also disconnecting the connector attached to it. Unplug all of the cords. Wait for a couple of seconds before connecting them again. Turn the printer on and hopefully, it should respond just fine.

What does it mean when your printer says ink absorber is almost full?

The message Ink Absorber Full is an indication that the machines internal ink absorbers are almost full. These ink absorbers are used to hold ink after it has been purged from the print head during the print head cleaning cycles. In order to clear this message the ink absorbers inside the machine must be replaced.

Bagaimana cara mengatasi error 5b00?

Berikut ini adalah cara mengatasi error 5B00 pada printer Canon IP2770. Pertama, hidupkan komputer atau laptop kemudian hubungkan printer Canon IP2770 ke komputer melalui USB seperti biasa. Pada langkah ini printer dalam kondisi mati. Kemudian, tekan tombol resume pada printer lalu tahan.

Siapa printer yang bisa mengatasi error 5b00?

Selain Canon IP2770 dan G2000, permasalahan 5B00 ini juga bisa terjadi pada beberapa jenis printer seperti IP2700, G1000, MP287, MG2570, E400, MP237, dan lainnya. Namun, meski tidak bisa dihindari, error 5B00 tetap bisa diatasi. 2 cara mengatasi error 5B00 Canon G2000 dan IP2770 bisa kamu gunakan.

Apakah error 5b00 bisa diatasi?

Namun, meski tidak bisa dihindari, error 5B00 tetap bisa diatasi. 2 cara mengatasi error 5B00 Canon G2000 dan IP2770 bisa kamu gunakan. Tidak perlu repot membawa ke Service Center, dengan 2 langkah di atas kamu bisa membuat printermu berfungsi normal kembali. Semoga bermanfat dan terus produktif!

author

Back to Top