How do I setup my comtrend AR-5381U wireless router?
How do I setup my comtrend AR-5381U wireless router?
Configuring the Comtrend AR-5381U Router 2) Click the “Advanced Setup” link on the left. 3) Click on the “WAN Service” link on the left. 4) Click on the “Edit” button on the row beginning with “ppp0”.
Is the comtrend AR-5381U a modem or router?
The AR-5381u is an IPv6 compliant, high performance 802.11n, 4-port Ethernet ADSL2+ Router with full routing capabilities to segment and route IP protocol. It features TR-069/098/111 and TR-068 compliance for hassle-free setup and configuration.
How do I log into my comtrend router?
Navigate to IP 192.168. You’ll need to navigate to the IP address of your router to access the setup pages. The most typical default IP address for Comtrend routers is 192.168. 1.1. Type it into the address bar of your browser and see if it takes you to the login for the setup pages.
How do I turn on WPS on my comtrend router?
1) On the front of your router, there is are two small round button labeled 2.4GHz WIFI ON/OFF & WPS and 5GHz WIFI ON/OFF & WPS. Press and hold the 2.4GHz button for approximately 20 seconds and release. Within a few seconds, the 2.4GHz WIFI LED will turn on. Repeat the same process for the 5GHz WIFI if needed.
How do I change my Consolidated WIFI password?
To change your password, please visit webmail.hickorytech.net. Click on the Forgot Your Password link next to the password field, and then click on the link that says Change Your Password. You will need to know your username, your current password, and the password you want to change it to.
How do I reset my Artrend AR 5319?
Reset the modem back to factory defaults by holding the small button on the back of the modem for about 10 seconds while the modem is powered up. You are successfully able to log into the modem. 1) From a web browser, go to “http://192.168.1.1”.
How do I change the SSID on my comtrend router?
How do I change the wireless information on my ComTrend Router?
- Enter 192.168. 1.1 in your address bar. Enter Username and Password. Username: root.
- Click on Basic Setup. –
- Click on Wireless. –
- Enter your new SSID (router name) Click Apply/Save. –
- Click Security. Enter password of your choice. Click Apply/Save. –
How do you find a router’s IP address?
Find Your Router IP Address on Android
- Go to Settings.
- Tap Wi-Fi Settings.
- Tap and hold on your connected network and select Manage Network Settings.
- Check the box next to Show Advanced Options.
- Select Static under IP Settings.
- Your router IP address is listed under the Gateway section.
Where is network security key on comtrend router?
To connect your WiFi devices to your new PG- 9172AC WiFi Access Point, select the PG-9172AC Access Point using your WiFi device’s standard network list. The Network Name (SSID) and Password (WiFi Key) can be found on the bottom of the PG- 9172AC.
What is the ar-5381u ADSL2+ router?
The AR-5381u ADSL2+ router also provides state of the art security features such as 64/128 bit WEP encryption and WPA/WPA2 encryption, Firewall, and VPN pass through. The AR-5381u is designed for both residential and business applications that require wireless and wired connectivity to an ADSL broadband network.
How many virtual connections does the ar-5381u support?
The AR-5381u supports up to 16 contiguous virtual connections allowing for multiple simultaneous Internet connections.
How do I update the firmware on my ar-5381u?
NOTE: If pressed down for more than 60 seconds, the AR-5381u will go into a firmware update state (CFE boot mode). The firmware can then be updated using an Internet browser pointed to the default IP address. fFRONT PANEL The Wi-Fi & WPS buttons are located on the bottom-left of the front panel, as shown.
How do I restore the default configuration of the ar-5381u-na2?
The factory default configuration can be restored either by pushing the reset button for more than five seconds until the power indicates LED blinking or by clicking the Restore Default Configuration option in the Restore Settings screen. 3.2 IP Configuration DHCP MODE When the AR-5381u-NA2 powers up, the onboard DHCP server will switch on.
