How to configure RSPAN?
How to configure RSPAN?
Configuring RSPAN
- On the source device, enter the configure terminal command to access global configuration mode.
- Enter the rspan-vlan command, specifying a VLAN ID, to define an RSPAN VLAN on the source device.
- Enter the tagged ethernet command, specifying an interface, to add a member port.
How does RSPAN work?
RSPAN works by mirroring the traffic from the source ports of an RSPAN session onto a VLAN that is dedicated for the RSPAN session. This VLAN is then trunked to other switches, allowing the RSPAN session traffic to be transported across multiple switches.
How to monitor port on Cisco switch?
How to: Monitoring traffic with Cisco port monitoring.
- Step 1: Connect to your switch (telnet, ssh, whatever method you want)
- Step 2: Enter enable mode.
- Step 3: Enter the configuration terminal.
- Step 4: Enter your interface’s configuration.
- Step 5: Configure which ports to monitor.
- Step 6: Save your configuration.
What is SPAN port on Cisco switch?
Destination (SPAN) port: A port that monitors source ports. This is usually the point to which a network analyser is connected. Remote SPAN (RSPAN): When Source ports are not located on the same switch as the Destination port.
What is Rspan port?
The Remote Switched Port Analyzer (RSPAN) enables you to monitor traffic on one switch through a device on another switch and then send the monitored traffic to one or more destinations.
What is reflector port in Rspan?
The reflector port is the mechanism that copies packets onto an RSPAN VLAN. The reflector port forwards only the traffic from the RSPAN source session with which it is affiliated. RSPAN extends SPAN by enabling remote monitoring of multiple switches across your network.
What is difference between Span and Rspan?
When you use a destination interface on the same switch as your switch we call it SPAN, when the destination is a remote interface on another switch we call it RSPAN (Remote SPAN). When using RSPAN you need to use a VLAN for your RSPAN traffic so that traffic can travel from the source switch to the destination switch.
How do I configure a port on a Cisco switch?
About This Article
- Connect to the switch.
- Run the enable command.
- Run the configure terminal command.
- Run interface port-id (replacing port-id with the port you want to enable).
- Run the “no shutdown” command.
- Run “copy running-config startup-config” to save your changes.
How do I enable terminal monitor on a Cisco switch?
You need to enable the logging monitor command on the destination R2….Then you can see the log of the interface status.
- R1#telnet 192.168.12.2.
- Trying 192.168. 12.2 Open.
- User Access Verification.
- Password:
- R2>enable.
- Password:
- R2# terminal monitor.
- R2#configure terminal.
Is Rspan Cisco proprietary?
SPAN (Switched Port Analyzer) is a Cisco Proprietary feature which allows to send a copy of traffic passing through ports to another port on the switch.As demand on deep packet inspection and analysis grew , so did the development on SPAN and Cisco cam up with RSPAN and ERSPAN.
What is remote span?
A remote SPAN (RSPAN) is sourced in the same manner as a traditional SPAN, either from individual ports or all ports in a VLAN. An RSPAN consumes one SPAN session in the same way that a local SPAN does, however, the RSPAN uses a VLAN for a destination instead of an interface.
How do I configure a switch port?
Switch ports can be manually configured with specific duplex and speed settings. Use the duplex interface configuration mode command to manually specify the duplex mode for a switch port. Use the speed interface configuration mode command to manually specify the speed for a switch port.
How many span sessions can I configure in a Catalyst 4500 switch?
You can configure (and store in NVRAM) up to five SPAN sessions in a Catalyst 4500 series switch. The five sessions can be split any way between SPAN, RSPAN source, and RSPAN destination sessions. The following sections describe how to configure SPAN. SPAN selects network traffic for analysis by a SwitchProbe device or other RMON probe.
How do I check the status of a span or RSPAN session?
The “Status” field in the show span and show rspan commands displays the operational status of a SPAN or RSPAN session. After the system is on, a SPAN or RSPAN destination session remains inactive until the destination port is operational.
What is the use of 4500 server?
07-20-2010 01:50 AM and 4500 is used as a server farm both are connected each other via trunk link. 07-20-2010 02:40 AM 07-20-2010 05:32 AM 07-20-2010 05:32 AM
Are inactive VLANs allowed for vspan configuration?
• Inactive VLANs are not allowed for VSPAN configuration. • A VSPAN session is made inactive if any of the source VLANs become RSPAN VLANs. In software release 6.3 (1) and later releases, you can enter the filter keyword to select a set of VLANs in a trunk that is used in a SPAN session.
