What angle should DSTV dish be?

What angle should DSTV dish be?

It should be at an angle of 53 degrees to the right of the satellite dish. If you don’t have a meter to measure, you can use the face of your analog clock to get the perfect angle at half-past four. When making the DStv dish alignment, you should also ensure it is facing eastwards.

How do I set the angle on my satellite dish?

To set azimuth:

  1. Use a compass to find the correct angle and move the plumb mast (the pole on which the dish is mounted) until the dish is pointing at that angle.
  2. Check your signal strength: anything over 40 is a good signal.
  3. Tighten all hardware.

Which direction must DSTV dish face?

Step one – Mount the dish properly When you receive your DSTV dish, you will notice that it comes with four cement screws. The first step will be to drill four holes into the base of the antenna mast, relevant to the mounting location, which will need an unobstructed view pointing to the Eastern part of the sky.

How do you set a LNB skew angle?

When standing in front of your dish, rotate the Feed/LNB assembly counter-clockwise for a + skew value or rotate the Feed/LNB assembly clockwise for a – skew value. Ignore any +/- on the scale (it may be the wrong way round). Numbers like 0, +45, -45, -90, +90 may also be back to front.

How do I set DSTV signal strength?

How To Fix Signal Strength On DStv?

  1. Check F-type connectors. Check for incorrectly connected F-type connectors on the LNB and at the back of the decoder.
  2. Correct the LNB alignment.
  3. Adjust satellite dish alignment.
  4. Replace a faulty LNB.
  5. Move your satellite dish.
  6. Cut down or prune trees that may obstruct the signal.

How do you set a LNB position?

How to Adjust the LNB on a Satellite Dish

  1. Enter your satellite box’s setup menu.
  2. Check transponders 1 and 2.
  3. Loosen the bolts that hold your dish in place.
  4. Move the dish experimentally from side to side and up and down; no more than 1/2 inch at a time.
  5. Secure the bolts to the dish back in place as tightly as possible.

How do I position my DSTV satellite dish?

The satellite is positioned at 68.5 degrees east. Make sure that there are no trees or any other obstacles like high buildings etc. between the spot that you have decided on and the position of the satellite. Install the dish on a secure wall and high enough so that it can’t be tampered with from the ground.

How do I set my DSTV signal?

Once you encounter a poor signal error, you can press the HELP button on your remote and click on General Information. Then, click on Select Tuner Status Signal Quality & Strength. Here you will be able to view the strength of the signal. All of these values should be either 50% or above.

How do I set DStv signal strength?

What is skew angle for satellite dish?

Skew angle refers to the angle at which a beam from a terminal location hits the satellite.

How do I install DStv installation wizard?

Running the installation wizard on the HD decoder

  1. Press the blue “DStv button”
  2. Use the right arrow to go to “Settings”
  3. Scroll down to “Satellite Settings”
  4. Then choose “Home Network”
  5. Select “Launch Installation Wizard” then press “OK” on the remote.
  6. Choose the satellite that matches your country.

How to realign a DStv satellite dish?

Realigning a DSTV satellite dish involves correcting the angle of the dish or the azimuth. In fact, you don’t even need a meter as many DSTV provides claim you should, all you need is a receiver, a TV and someone to help you monitor the signal while you’re fixing the satellite dish.

Where can I get a DStv satellite dish in Gauteng?

Aerial and Satellite Excellence are DSTV approved installers in Gauteng. Take a look at our vast array of services on offer today. Speak to one of our friendly staff members about Third View and DStv Extra View price setup for multiple viewing pleasure. Do you know how to install a DStv satellite dish yourself?

How do I change the DStv alignment with Multichoice?

Multichoice makes DStv alignment easier by including a small bracket on the satellite dish. It is marked with the correct 36.6 degrees required. You should also check the angle of your smart LNB and change it while changing the DStv alignment. It should be at an angle of 53 degrees to the right of the satellite dish.

How do I connect the satellite dish to the LNB?

Use the satellite field strength meter to line the satellite dish up with the satellite (68.5 degrees east) Set the LNB and connect the cable to the LNB then seal the connection with waterproof tape Fasten the cables on to the dish with cable ties


Back to Top