Where is the transmission fluid filter usually located?
Where is the transmission fluid filter usually located?
What Does a Transmission Filter Do? The transmission filter is located above the transmission pan, which is the component that catches the excess fluid. The filter is also situated below the pickup tube, which connects to the oil pump.
How many quarts of transmission fluid does a 545RFE take?
You will also need approximately 8 quarts of ATF 4+ transmission fluid. The converter plus transmission holds approximately 16 quarts(I think), but this service will change out about 6-8 quarts of the total.
What kind of transmission fluid does a 545RFE take?
The capacity of the 545RFE transmission is 10.5-11 l, while the fluid type is Dexron 3-6 or MOPAR +4. Some models with the ‘Tow/Haul’ mode were able to make faster shifts to cut wear on the 545RFE transmission.
How can you tell the difference between a 45RFE and a 545RFE?
The 45RFE and 545RFE are identical mechanically. The difference is in the software. Before you drop the transmission, though, pull the trans oil pan off and look at the valve body. On the passenger side of the main valve body is a cover plate that covers the accumulator pistons.
How do I know if my transmission filter needs to be changed?
Signs Your Transmission Fluid Filter is Clogged (And What To Do About It)
- An Unexplained Rattle. Sometimes, you know exactly what’s making your vehicle rattle.
- Whirs or Whines.
- Leaking.
- Burning Smell.
- Problems Changing Gears.
- A Noisy Neutral.
- Take Care of Your Transmission Fluid Filters.
How do you unclog a transmission filter?
Hold the filter pieces over a pan and spray them with disc brake cleaner to clean them. The dirt and particles will drip off into the pan. Anything that is still stuck to the filter pieces can be dislodged with a toothbrush.
Is the 545RFE Transmission good?
it’s a fairly reliable transmission, although it can stand to be tuned for better performance. its good to around 400-450 horsepower before you would need to upgrade it. just do your normal maintenance on it and you should be fine as long as you own it.
Who makes the 545RFE transmission?
Chrysler RFE
| Chrysler RFE transmission | |
|---|---|
| Overview | |
| Manufacturer | Chrysler Corporation |
| Also called | 45RFE/545RFE 68RFE 65RFE/66RFE |
| Production | 1999-present |
How does a 545RFE work?
In the 545RFE four gears are used on the upshift and a new “gear”, 2nd Prime, was used with a different (1.50:1 rather than 1.67:1) ratio to increase versatility when downshifting. Although, with some tuning, you can get the 545RFE to upshift into 2nd Prime.
How do I identify my Chrysler transmission?
How do I Identify Chrysler Transmissions?
- Determine if the transmission is an automatic or a manual, also known as a standard transmission.
- Go underneath the vehicle to access the transmission.
- Count the number of bolts and view the transmission pan shape on the automatic transmission.
Is it OK to change transmission fluid without changing the filter?
Many transmission manufacturers use only a screen on the fluid pickup to filter out any casting flaws or debris that could be poured down the dipstick. Some manufacturers do not recommend changing the filter. The fluid will break down and needs to be changed, the filters do not plug up on a healthy transmission.
What happens if you don’t change your transmission filter?
If the filter fails to do its job properly, the transmission fluid will quickly reach a point where it is too dirty to do its job efficiently. Where the contamination reaches a certain level, it can burn and lead to transmission repair being required.
Are the 545 and 545RFE transmissions the same?
As for the 545 services, the same tranny casing is used on the 45RFE, 5-45RFE, and 68RFE, so this procedure is the same for these transmissions as well, but check part numbers and fluid capacities. The 4.7L and the 5.7L HEMI use the same transmission, so it should also be the same filter part numbers for both engines.
How do you change a 545RFE transmission solenoid?
All you need to do is remove the fluid container, pop out the old solenoid, and pop in the new solenoid. Be sure to match the color-coded wires on your new solenoid to the wires on the old solenoid. The 545RFE transmission occasionally has problems with the pressure sensor, which is mounted on the side of the transmission.
How many quarts of transmission fluid does a 545 take?
You will also need approximately 8 quarts of ATF 4+ as 545 transmission fluid. The converter plus transmission holds approximately 16 quarts. Who makes the 545 transmission? The RFE is an automatic transmission family from Chrysler.
What happens if the pressure sensor on a 545 transmission goes bad?
If the pressure sensor has completely gone bad, the transmission may stall or overheat. Replacing a bad pressure sensor is relatively easy on the 545RFE transmission, as the pressure sensors are located in an easily accessible location on the side of the transmission.
