Can a ledger board be cantilevered?
Can a ledger board be cantilevered?
Chuck Lockhart A deck ledger cannot be attached to cantilevered house framing. Instead, build the deck to be freestanding. Chuck Lockhart Alternatively, you can build the deck so that the deck joists extend into the house and bear on a wall plate or mudsill.
How do I add flashing to an existing deck?
To add flashing, first remove the deck board that runs alongside the house. If the boards run diagonally, snap a chalk line 5-1/2 in. from the house, then set the blade in a circular saw to the depth of the decking boards and cut off the board ends. (Replace the cutouts at the end of the job with a 5-1/2-in.
How do you attach a ledger board to stucco?
Cut a groove and insert the flashing for your ledger on stucco installation.
- Cut a straight line an inch into the stucco with circular saw.
- Insert flashing into the groove that was just cut.
- Predrill holes in the stucco and ledger.
- Fasten ledger to the house with lag screw.
Can you extend a ledger board past the house?
If your ledger board will continue around the corner of your house, you will also have to remove the house siding corner post in addition to the siding. Sometimes, you may want to extend your ledger board beyond the house to function as a beam with a post connection at the opposite end.
How far can I span a 2×8 for a deck?
Using this rule, a 2×6 will span 9 feet, a 2×8 will span 12 feet, and a 2×10 will span 15 feet. As you can see, the larger the depth, the longer the span.
Does a deck need a ledger board?
Yes, the deck needs to be tied to the house. You will want to install a ledge board that’s lag bolted to the structure of the house. That means through the brick/sheathing and into the rim joist. And, of course, you should use the appropriate metal hanger to tie the joists of the deck to the ledger board.
Do you need flashing on a deck?
“Flashing is required where exterior porches, decks, or stairs attach to a wall or floor assembly of wood frame construction.
How do you secure wood to stucco?
Align the wood’s hole with the hole in the stucco. Mount a lag screw’s head into the nut driver. Press the screw tip through the wood and through the hole in the stucco until the tip rests against the stud. Drive the screw into the stud until the screw’s head pulls the wood flush against the stucco surface.
How do you attach a ledger board to a house for a patio cover?
Attach the ledger with 1/2-inch-diameter lag screws or bolts every 16 inches (or as specified by local building codes). Slip stainless-steel washers between the ledger and the siding to allow water to flow behind the ledger. If you can’t get behind the joist to cinch down nuts, use lag screws.
How does a deck ledger work?
Most house framing relies on building elements (floors, walls, roofs) being stacked one atop another. A ledger relies on the fasteners and strength of the wood ledger board and rim board of the house to carry the deck live and dead loads. Attaching a deck ledger securely is only half the work of installing a ledger.
What is a ledger on a house?
The deck ledger to the house is an unusual connection in home building. Most house framing relies on building elements (floors, walls, roofs) being stacked one atop another. A ledger relies on the fasteners and strength of the wood ledger board and rim board of the house to carry the deck live and dead loads.
Can a deck Ledger be attached to a cantilevered floor?
A deck ledger cannot be attached to the rim board of a cantilevered floor. The rim board must be solid sawn lumber or certain types of engineered rim board. The IRC’s deck ledger fastening table is the most restrictive.
How do you attach a ledger to an existing building?
Our approach solves this by properly flashing the building at the point of connection with the ledger, and then holding the ledger off the face of the building with simple spacers. Remove siding where ledger is to be attached and fold up and pin existing building membrane above install zone.
https://www.youtube.com/watch?v=A8MJrFiXHcQ
