How do I remove a fireplace insert?
How do I remove a fireplace insert?
- Step 1: Remove the Trim. Using a hammer, mallet, or pry bar, you will want to remove the trim and any nails around the fireplace that is holding the insert in place.
- Step 2: Disassemble pipes and Vents. This is the step where you are disconnecting everything.
- Step 3: Pry the Insert.
- Step 4: Set it off to the Side.
How do you remove a cast iron fireplace insert?
Unfasten the vent line going up into the chimney using your screw gun to free it from the top of the cast iron insert. Put on gloves and ask your assistant to put on gloves as well. Lift and pull the cast iron fireplace insert out of the firebox, resting it on the cardboard covering the hearth to complete the removal.
Is it easy to remove a fireplace insert?
A wood-burning fireplace insert must be removed when your fireplace and chimney enclosure need cleaning. It’s easier than removing a gas insert because it’s not necessary to remove or disconnect gas lines. If you don’t want to hire a professional to remove the fireplace insert, you can attempt to remove it yourself.
How do you remove a coal fireplace insert?
Start by shutting off the gas to your home at the main valve so there’s no chance of a leak. Take a crowbar and remove the trim around the insert. When you can access the gas line, remove it as well. Then, carefully wiggle the insert out of the fireplace and remove it.
How much does it cost to remove a fireplace insert?
Cost to Remove a Gas or Electric Fireplace Insert When a professional takes out the insert alone, expect to pay between $250 to $600. However, you’ll need a plumber qualified to work with gas lines or an electrician to disconnect the insert from its fuel source. This will run an additional $100 to $300.
How do you remove a log burner?
How to Remove Wood Burning Stoves
- Open the doors of the wood stove to sweep out ash and remove any wood inside.
- Close the dampers to prevent residual ash from falling onto the floor when you move the stove.
- Spray lubricant around the pipe connection with the stove and let it set for at least 10 minutes,.
How do you remove a factory built fireplace?
The flue is likely held in place by some screws holding the flange. Removing the screws will allow the flue to come loose and the unit to be pulled free. If the unit is gas-burning, the gas leading to the unit will need to be turned off. Then the gas line can be dismantled and pulled away from the unit using a wrench.
How much does it cost to remove a wood fireplace insert?
Removing a wood-burning insert should only cost between $500 and $1,000 with the help of a professional. You may want to call a fireplace pro simply due to the insert’s size—more on this below—but it’s not always necessary unless you’re removing more of the fireplace or chimney structural support.
How do I replace an electric fireplace insert?
How To Install An Electric Fireplace Insert
- Remove The Existing Installation And Clean Your Fireplace.
- Make Sure Your Fireplace Is Waterproofed.
- Seal The Damper.
- Power Supply / Outlet.
- Install The Insert.
- Power It Up and Test It.
- Install The Trim.
How do you install a Kent Fire in a chimney?
Determine whether the flue pipe will fit vertically in the chimney from the heater to the cowl. Install the selected Kent wood fire into the prepared fireplace. Once in position and level fix the fire to the base of the fireplace enclosure with suitable anchors.
How do you clean the inside of a fireplace insert?
Open the doors of the fireplace insert, if they have been installed. If an ember shield is being used, fold it up and set it aside. Remove the metal grate used for the wood. Remove soot from the bottom of the insert and place it in a bucket, using a metal scoop.
How do you remove an electrical insert from a wood stove?
Removing a Wood-Burning or Electrical Insert Remove all of the trim from around the fireplace insert. Remove any nails holding the insert flashing to the wood framing. Disassemble any pipes, vents, or other pieces of the insert. Pry the insert out of place with a crowbar. Place thick carpet on the floor in front of the hearth.
However, you may only need to have a partial removal in order to have the fireplace insert taken out. It can cost anywhere from $500 to $2,500 for the project to be completed by a professional. Try calling around a few removal services in your area to get a quote so you can compare the costs.
