When was the Icom IC-7300 released?
When was the Icom IC-7300 released?
The Icom IC-7300 saw its debut at the Tokyo Hamfair August 22, 2015. This new HF plus 6 meter 100 watt transceiver hosts new capabilities and technologies for its class.
What does IC-7300 include?
The Icom IC-7300 features a RF direct sampling system, 15 discrete band-pass filters, a real-time spectrum scope and a large 4.3″ color touch screen display. Additional features of the IC-7300 include a built-in automatic antenna tuner, 101 channels, SD memory card slot and 3 CW functions.
What bands does ICOM 7300 cover?
(Guaranteed range: 0.500–29.999, 50.000–54.000MHz,70.000–70.500MHz.) * 70 MHz band is for EUR version. Each frequency range is differ according to versions.
Do I need a power supply for ICOM 7300?
Does it come with an integrated power supply or internal battery? You need to purchase an external power supply. I use the TekPower TP50SW 50 Amp 13.8V Analog Power Supply. It works nicely with the IC-7300.
Where is ICOM 7300 made?
ICOM IC7300 – still made in Japan.
Does ICOM 7300 have Bluetooth?
It is possible however to add a very small Bluetooth transmitter to the 3.5mm headphone jack and then use a pair of Bluetooth headphones around the shack. …
Is ICOM 7300 a SDR?
A first in an amateur radio transceiver, the IC-7300 utilizes technology seen Software Defined Radios (SDR) and other radio equipment. This RF direct sampling system promotes a high performance spectrum scope and superior phase noise.
Does IC-7300 have D star?
Using the IC-9700 and IC-7300 creates the ultimate, compact radio station covering the VHF, UHF, HF and 1200 MHz bands. The IC-9700 is the only VHF/UHF all mode transceiver that enables a variety of VHF/UHF operation including DX, contests, satellite/EME and D-STAR.
How big is the ICOM IC 7300?
240×94×238mm
| General | |
|---|---|
| Frequency stability | Less than ±0.5ppm (–10˚C to +60˚C; 14˚F to 140˚F) |
| Frequency resolution | 1Hz |
| Dimensions | 240×94×238mm; 9.45×3.7×9.37in (projections not included) |
| Weight (approximately) | 4.2kg; 9.26 lb |
Does the IC-7300 come with a power cable?
A new IC-7300 comes with the power harness that plugs into the radio.
What is the best power supply for the ICOM 7300?
Power Supply for Icom IC-7300. The Icom PS-126 switching power supply provides 13.8 VDC ± 5%, at 25 Amps. The input voltage is 120 VAC (85-135 VAC). The PS-126 may be configured as a tall or short power supply based on how the rubber feet are attached.
Where is the ICOM 7300 made?
How much does the ICOM IC-7300 HF transceiver cost?
Free Shipping! ICOM IC-7300 HF plus 50 MHz RF Direct Sampling 100 Watt Transceiver with Touchscreen Regular Price: $1,299.95
What is the IC-7300 resources page?
The basic intent of the IC-7300 Resources Page is to act as a single focal point for all information to do with the IC-7300. Newcomers to the rig should find this particularly useful and convenient. Note that no original documents are stored anywhere on the Resources Page. Instead, all table entries are URLs pointing to the documents themselves.
Does the IC-7300 use the ltc2208-14?
Although unconfirmed by Icom, apparently they use in the IC-7300 the 14bit Linear Technology LTC2208-14, sampling at ~124Msps. This is not a new part (actually, it’s 9 years old) but it’s good enough and it has been used before in SDR equipment for amateurs, although most opt for the higher-spec LTC2208 16-bit version.
What is the resolution of the IC-7300 display?
Icom Transceiver Display Sizes and Resolution IC-7300 : 4.3 inches (RayStar RFE430H) 480 x 272 IC-7600 : 5.8 inches (EPSON L5S30853P00) 400 x 240 Again, we found the sensitivity of the spectrum scope to be excellent as well.
