Other

How do you get a 2D radiation pattern in HFSS?

author 0

How do you get a 2D radiation pattern in HFSS?

  1. 1) Firstly, setup for Radiation sphere:
  2. In group of Phi: start = 0 degree.
  3. In group of Theta: start = 0 degree.
  4. 2) Create​ report:
  5. HFSS-> Results -> create far field report -> Radiation pattern :
  6. by this method you will get Both E-plane and H-plane in one plot.

What is 2D radiation pattern?

Radiation Pattern in 2D Two-dimensional pattern can be obtained from three-dimensional pattern by dividing it into horizontal and vertical planes. H-plane represents the Horizontal pattern, whereas V-plane represents the Vertical pattern.

How do you plot 2D gain in HFSS?

For plotting the gain vs frequency 2D plot you need to do following steps: 1….For Gain Vs Freq in HFSS follow the below steps:

  1. Result -> Farfield report -> Rectangular tupe.
  2. Select Sweep (Solution type) -> Gain -> Total Gain -> dB.
  3. Select desired Frequency.
  4. Families – > Select desired angle.
  5. Plot.

How do you plot radiation efficiency in HFSS?

look for infinite sphere.. – click on infinite sphere..then click “compute antenna parameters”. Open HFSS of your design and simulate,then go to result and follow the procedure. Results>create far field>rectangular plot>antenna parameters>radiation efficiency >absolute.It must be frequency Vs Radiation eff.

How do you find the radiation pattern of an antenna in HFSS?

In HFSS go to HFSS tab> Results> Create Far Filed report> Radiation pattern> select trace tab> select directivity > select DirPhi and DirTheta > select dB> go to familes tab and select phi=0 (for E- Plane) or phi=90 (for H-Plane) > then click New Report.

How do you plot 3d radiation patterns in HFSS?

Go to the project manager window —>right click on “radiation” —-> “insert far field setup” and set the range of phi and theta. This complete your far field setup. A window will open and tick under “visible” and then apply.

What is antenna used for?

The antenna is a device that is used for transmitting and receiving signals, which represents some information. It was invented in the year 1888 by Germans. They are designed for wireless communication and have the capability to propagate both radio and microwave signals.

How do you test for Gain in HFSS?

In HFSS go to HFSS tab> Results> Create Far Filed report> Rectangular Plot>select trace tab> Prime Sweep: select Freq> select Gain > select dB> go to familes tab > select Theta=0 and Phi=0 >then click New Report. Fallow this step and we have seen Gain Vs Frequency plot in HFSS.

How do you plot Gain in DBI in HFSS?

gain dbi with hfss Results -> Create Far Field Report ->Rectangular Plot -> and choose Gain on menu “Category”. I have the Beta version too, and i can plot the Gain. I hope that help you.

How do you plot gain of antenna in HFSS?

In HFSS go to HFSS tab> Results> Create Far Filed report> Rectangular Plot>select trace tab> Prime Sweep: select Freq> select Gain > select dB> go to familes tab > select Theta=0 and Phi=0 >then click New Report.

How to create E-plane and H-plane Co and cross radiation patterns in HFSS?

In HFSS go to HFSS tab> Results> Create Far Filed report> Radiation pattern> select trace tab> select directivity > select DirPhi and DirTheta > select dB> go to familes tab and select phi=0 (for E- Plane) or phi=90 (for H-Plane) > then click New Report. Fallow this step and we have seen E-Plane and H-plane co and cross radiation patterns in HFSS.

How to generate radiation patterns using HFSS simulation tool?

After simulation, Go to Results->create farfield report->radiation report->In geometry select proper infinite sphere and other settings like rE or Gain in db. By using HFSS simulation tool, you have to generate XY, YZ and XZ planes radiation patterns. All the best. Welcome. Most Welcome, I hope it helps.

How to create far filed report in HFSS?

In HFSS go to HFSS tab> Results> Create Far Filed report> Radiation pattern> select trace tab> select directivity > select DirPhi and DirTheta > select dB> go to familes tab and select phi=0 (for E- Plane) or phi=90 (for H-Plane) > then click New Report.

What is ANSYS HFSS?

ANSYS HFSS is an industry standard tool for simulating 3-D full-wave electromagnetic fields. Students registered in ECE451 can get free access to ANSYS HF package from the University of Illinois Software Webstore.

author

Back to Top