Can you hem jeans and keep the original hem?

Can you hem jeans and keep the original hem?

Fabric no longer bunches when hem is folded up! Having reduced the leg width along the inner leg, you can proceed with hemming the jeans with the original hem (same as the instructions for the straight leg jean). FOLD, PIN, SEW and CUT same as above. Frayed jeans are all the rage these days!

How do you put an original hem on jeans?

Instructions:

1. Determine Length. Instead of going by your typical inseam length, try on your jeans (don’t forget to wear shoes) and then evaluate the length.
2. Fold and Pin.
3. Measure.
4. Unpin and Repin.
5. Fold Up the Hem.
6. Stitch Below the Hem.
7. Trim and Serge.
8. Press and Topstitch.

How do I stop my jeans from rolling up in the hem?

Thread your sewing machine with thread that matches your original hem thread. Sew your hem into place using a seam allowance equal to the original seam allowance you measured. Remove your pins. The interfacing will keep your hem in place and protect it from curling.

How do you hem pants and keep the original hem?

1. Try on your to-be-hemmed pants. Tuck the hem under to your desired length.
2. Take off jeans and turn inside out.
3. Take out all your pins and turn jeans right side out.
4. Using your heavy duty needle and matching thread, sew a straight stitch very close to the existing hem.
5. Fold hem down.

What to do when your bootcut jeans are too long?

What to Do If Your Jeans Are Too Long

1. Wear Them Higher on Your Waist. If your jeans are too long, try wearing them higher on your waist.
2. Shrink Them. If your jeans are both too long and too wide, you can try shrinking them.
3. Roll Them Up.
4. Choose Selvedge Jeans.
5. Place Over the Top of Your Footwear.
6. Buy Custom-Sized Jeans.

Why do my jeans curl at the bottom?

Typically that condition results from the fabric not being cut perfectly on grain, when your pattern pieces of the jeans were cut out in the factory. And then ,very often the jeans are stretched at the hem, as they are fed through the hemming machine which causes more distortion…

What is the best way to hem jeans?

Pin the pants at the length you want. This step is easier if you get someone to help. Put the pants on and stand on a step stool. Have the assistant turn the fabric under and pin each leg to the correct length. Take off the pants and evenly fold the fabric under all the way around each leg where the hem needs to be.

How to hem jeans professionally?

Step One: Next,with the jeans on the wearer,fold the hem up to find the best length.

Step Two: Measure the total amount of jean that need to be removed,so if the total folded up part is 5 inches,that will be your measurement for the

Step Three: Alright,take a deep breath,make sure your marking is correct…

Step Four: Time to reattach!

How to hem jeans tutorial?

1) Decide where to hem. Try on your jeans and decide where you would like to hem them. Generally, jeans should fall about an inch above the floor. 2) Fold up the bottom. Create a cuff where you want the jeans to be hemmed. 3) Pin the hem in place. Place straight pins around the circumference of the pant leg to hold it in place. 4) Sew the hem. Stitch around the circumference of the pant leg just below the stitching for the existing hem. 5) Unfold the hem. Tuck the excess fabric of the folded cuff up into the leg of the jeans, folding the original hem down so its outer side shows once 6) Iron the jeans. Use an iron to flatten out the hem you’ve created along the bottom edge.

How do I Hem pants with zippers on the legs?

1. Pin the zipper to the hem with the right side of the zipper facing the hem. The zipper start and end: Should be at the inseam – zipping the pant legs is too difficult if the start is on the outside seam. Should barely meet.