How do you lubricate a motorcycle speedometer cable?

How do you lubricate a motorcycle speedometer cable?

Starts here2:17How-To: Lube Motorcycle Cable – YouTubeYouTubeStart of suggested clipEnd of suggested clip48 second suggested clipI have this cable Luber tool there just there’s a closed end and an open end you want to take theMoreI have this cable Luber tool there just there’s a closed end and an open end you want to take the open end face it towards the the cable itself and then just slide the actual cable through.

Can you lube a speedometer cable?

Starts here2:35How To Lube A Speedometer Cable – YouTubeYouTubeStart of suggested clipEnd of suggested clip55 second suggested clipYeah this stuff is what was recommended to us. And basically all you got to do is a squirter inMoreYeah this stuff is what was recommended to us. And basically all you got to do is a squirter in there. And clean up whatever mess.

What do you use to lube a speedometer cable?

Even the smallest grains of sand that enter the speedometer cable housing can eventually destroy the cable by grooving or fraying it. Apply a liberal amount of grease on the cable from one end to the other. Use back-and-forth strokes evenly over the entire cable surface, stopping about 3 in. from each end.

How do you lubricate a speedometer?

Starts here1:51Lubricate Speedo Cable Making Noise – YouTubeYouTubeStart of suggested clipEnd of suggested clip61 second suggested clipSo I start spraying some lubricant down the whole inside there it’s got four sides to it two squareMoreSo I start spraying some lubricant down the whole inside there it’s got four sides to it two square cable that goes in there a big long cable. And is turning smoother.

What is graphite oil?

Graphite grease is a form of graphite lubricant that is designed to stick to a surface, such as when used on an exposed bearing. The grease will help keep the graphite in place so it can work.

How do you service a speedometer cable?

Starts here7:01How To Fix A Shaky/Bouncing Speedometer [BEST CABLE LUBE]YouTube

How do you fix a bouncing speedometer?

How do you clean Speedo cables?

Gently pull on the inner cable and it will come out of the outer sheath. Clean all the old grease and rust off the inner cable. (I used brake cleaner). I also held the sheath up as high as I could and sprayed brake cleaner into the sheath a few times until what came out when I let it down was clear.

What is graphite lube made of?

Graphite is structurally composed of planes of polycyclic carbon atoms that are hexagonal in orientation. The distance of carbon atoms between planes is longer and, therefore, the bonding is weaker. Graphite is best suited for lubrication in air. Water vapor is a necessary component for graphite lubrication.

Why graphite is a better lubricant than oil?

The greatest benefit to using graphite (rather than oil) is that the graphite leaves no sticky residue that may later attract dust. This is because the lubricating properties of graphite lie in its weak covalent bonds that allow the layers of graphite to “slide” on top of one another with very little resistance.

What causes speedometer needle to bounce?

While you are driving, if you notice the needle on the speedometer jumps erratically from one number to another, the speedometer cable is most likely damaged or the sensors on the driveshaft are not accurately sending the signal through the cable. If this occurs, the entire cable and housing needs to be replaced.

How do you lubricate a speedometer cable?

Pull the cable loose from the speedo and pack some grease in the plastic end. Then snap it back on the speedo head. Click to expand… Well the speedo cable is brand new so you guys think that lubing it will definetly help it stop bouncing.

How do you install speedometer?

Installing the New Speedometer Set the new speedometer in place on the instrument panel. Reconnect lighting connections for the speedometer. Slide the instrument cluster back into position. Replace the panel face plate in front of your instrument panel. Reconnect your car’s battery. Check the speedometer’s calibration.

How is a speedometer calibrated?

A speedometer has to be calibrated in order to ensure that the magnetic field torque accurately reads or displays the speed of the vehicle. It must take into account the gear ratio of the drive cable, diameter of the tires, and drive ratio in the differential. If any of these factors are changed on an automobile, the speedometer must be calibrated.

Does a car speedometer measure speed?

A car speedometer measures speed: how fast the car is moving. Speedometers measure speed in miles per hour or kilometers per hour. Some gauges display both readings. Speedometers have been standard equipment in automobiles since 1910.