How far up stove pipe should damper be?
How far up stove pipe should damper be?
approximately 12 to 18 inches
A damper is usually located approximately 12 to 18 inches from the stove, prior to the spot where the pipe exits into a chimney, if present. The damper retains heat that escapes up the chimney or flue. It allows this heat to dissipate into the area being heated by the woodstove.
What temperature should my wood stove pipe be?
I usually get the pipe to 500 – 550 upon initial start up and close down the air to run the. I would like to run the stove top temp to 600 as Jotul says the best range is 400-600. **All temp readings are the surface temperatures. 275 to 500 is what my manual says for my flue.
Does wood stove pipe need to be insulated?
Heating with wood can be very rewarding. When a properly lined chimney is not an option, a wood-burning stove can be installed with Class A insulated stainless steel stove pipe. Pipe mounted on the outside of a home or installed in an unoccupied space does not need to be enclosed.
Should I put a damper in my stove pipe?
Newer models of wood stove don’t typically require a damper. A damper was traditionally used on older, less efficient, models of stove to help reduce the flow of air leaving the firebox. Certified modern stoves meet stringent regulations and typically won’t need a damper to perform well.
What should my flue temp be?
You need at least 250 F all the way to the top to avoid water condensation and creosote formation. Depending on how tall your flue is and how well insulated what you have may be enough, wasted heat, or not sufficient.
Can I insulate a flue pipe?
Because the flue is carrying exhaust from natural gas or propane being burned, it can get hot. This can be a problem when the flue runs into your attic on its way to the roof, as it can heat your attic. Insulating the flue pipe can contain the heat, keeping your attic cooler.
Can wood stove pipe through wall?
If you’re setting up a wood-burning stove or pellet stove, running the chimney pipe through an outside wall saves the time and costs of installing a vertical chimney that requires a ceiling collar and roof flashing. For brick or stone walls, enlist a professional to cut the holes.
Why does my wood stove blowback?
A blow back occurs when the stove gets a “breath of fresh air” from a down draft or just an area of wood in the stove that is just about ready to flash over. When it ignites it sometimes will ignite the rich smoke in the stove quickly enough to increase the pressure within the stove.
Can you put too much wood in a wood stove?
Over firing a wood burning stove can cause long-term or permanent damage to the main components inside a stove. Placing too much wood into a stove or allowing too much air flow to the fire can cause the stove to over fire.
What is the flue on a wood stove?
A flue pipe is a vital part of the exhaust system of the wood stove installation. The flue gases which are released as a result of combustion of wood fuel are hotter than the normal temperature and automatically go upward so it is preferred to install the wood stove flue and chimney in the upward direction.
What is the temperature of stove pipe?
Over 900 degrees F: a hot fire can prematurely corrode and degrade the metal flue pipe and the wood stove. When over 900 degrees it is time to stop stoking the fire and turn down the damper. Between 400 and 900 Degrees F: This is the cozy temperature for a wood stove.
What is a gas wood stove?
Wood gas is a syngas fuel which can be used as a fuel for furnaces, stoves and vehicles in place of gasoline, diesel or other fuels.
Will a wood stove heat my garage?
You can absolutely install a wood-burning stove in your garage. These stoves are ideal for keeping you warm while fixing your car or tinkering around with tools. When you set up a wood-burning stove, you should always place it on a non-flammable, fireproof surface.