How do I fix the Sud error on my Kenmore Elite washer?
How do I fix the Sud error on my Kenmore Elite washer?
SUD : The Sud error code is used to indicate there are too many suds for the washer to remove. This is often caused by too much detergent being used or non HE detergent being used in an HE machine. Run the machine through a Rinse/Spin cold water cycle then a Normal cycle without adding any additional soap.
Why is my washer stuck on Sud?
If your washing machine has the word “SUDS” on the display, it has detected an over-sudsing condition, and will stop for a short period to allow the suds to dissipate. This error code is usually caused by too much detergent, or the wrong type of detergent. There are many different concentrations of laundry detergent.
How do I reset my Kenmore Elite he3?
How to Reset a Kenmore Elite HE Washer
- Press the “Stop” button twice, and then press the “Power” button. Video of the Day.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
Where is air trap Kenmore Elite washer?
The air dome is located on the back of the tub on the left hand side. If the pressure switch hose and the air dome is clear of any blockages the likely failure is the water level pressure switch. Check if pressure hose is fixed correctly. Check if the Air trap/Air dome is not blocked.
How long does Sud error last?
If you have noticed a SUD code during a washing cycle, it means the suds have exceeded the drum’s usual level. More specifically, this error means that the washing machine is reducing foaming. It has just stopped for 5-10 minutes to allow the suds to dissipate and the washing cycle to go on.
What does Sud lock mean?
Suds lock is the linking of the outer water jacket and the spin bowl with frothy detergent. It makes the spin bowl hard to turn so placing a greater load on the electric drive motor.
How do I fix my SUD error?
How to fix the error
- Wait for a little for the suds to dissipate.
- Clean the drain filter upon completing the wash cycle;
- Remove excess powder by running the washing machine without clothes and setting a long wash cycle and high temperature;
- Change the detergent if you notice a lot of suds.
What does Sud mean on Kenmore washer?
If “Sud” is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent.
How do you unlock a Kenmore Elite he3 washer?
There is a tab on the bottom of the door lock assembly that you can pull until it clicks to manually unlock the washer door.
How do you start a Kenmore Elite he3 washer?
Close the washer lid, making sure that no clothes are sticking out or preventing the lid from closing fully. Press the “Power” button on the control panel of the Kenmore Elite HE washer to turn on the display and begin programming.
What does HF mean on Kenmore Elite washer?
The FH error code indicates that the washer control does not detect water entering the machine within 30 seconds after the fill valves have been opened. It is also displayed after 8 minutes if the flow sensor has detected 10.5 gallons passing through it without the water level pressure switch tripping.
How do you run a diagnostic on a Kenmore Elite HE4t washer?
Here is what I did to run a diagnostic.
- With the washer empty, close the door.
- Push “control/on” or “Start”
- Select “Drain/Spin”
- Select “No Spin” by pressing SPIN SPEED touchpad.
- Push “PREWASH” option four times within 5 seconds.
- C:00 should light up and begin the diagnostic.
How do I fix a Kenmore Elite He3 washer with Sud error?
Use HE (high-efficiency) detergents if the SUD error shows. Kenmore’s Elite HE3 washer has a comprehensive error reporting system. The error messages appear on the display along with a tone sound.
What does Sud mean on a Kenmore Elite washer?
“SUD” means that the Suds Routine has run and excessive suds remain and have been detected. “F20” indicates a water inlet problem with no or insufficient water supply. “F21” is a drain problem.
Why is there a Suds lock on my Kenmore washer?
If “Sud” is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent.
What does error error code mean on Whirlpool washer?
error code is used to indicate that there are too many suds for the washer to remove. This is often caused by too much detergent being used or non HE detergent being used in an HE machine. Follow steps below to remove code. : Check the drain hose and make sure the hose is not plugged or kinked.
