How much horsepower does a 3800 engine have?
How much horsepower does a 3800 engine have?
The 3800 Series III engine, found in the Grand Prix, offered 200 horsepower for the sporty sedan base model. The supercharged 3800 Series III, found in the Grand Prix GT or GTP (depending on model year), unleashed 260 horsepower.
What was the last year for the GM 3800 engine?
1988-2003: The 3800 becomes GM’s workhorse engine. The engine grew to 225 cubic inches in 1964. Production stopped in 1967, and GM sold engine and production tooling to the Kaiser-Jeep Corp., the company that owned the Jeep brand.
How much HP does a 3.8 V6 have?
An Awakening… In box stock form, the 3.8L Essex V-6 produces 145-150 hp at the crankshaft. According to Super Six Motorsports, that’s 0.625 hp per cubic inch or 38.2 hp per liter.
How good is the 3.8 engine?
The 3.8 liter V6 was a conservatively designed, wider-bore, longer-stroke version of the then-new 3.3-liter V6. It was a good, solid engine from the start – not the highest performer or the lowest, but relatively quiet, driveable, and reliable….Premium Member.
| Category | 3.8 Liter |
|---|---|
| Fuel | Regular (US: 87 octane) |
Are all 3800 Series 2 the same?
1 Answer. They are both series II’s, the engines are the same. GM updated the EFI on most vehicles between ’99-’00. You will need to swap all six injectors and you may need to swap some sensors.
Do they still make the 3800 engine?
The venerable and immensely popular Buick V-6 survives today as the GM 3800 and serves as the base engine for many Chevy cars. It can trace its origins to the 198-cubic-inch V-6 that powered the 1962 and later Buick Specials.
Why did they stop making the 3800?
The 3.8 was discontinued in 2009. The 3.6 engine has had timing chain problems and the gas mileage is less than the 3.8. Seems like a step in the wrong direction.
Why did GM get rid of the 3800?
GM couldn’t get consistent quality from the difficult-to-cast aluminum blocks, so it dropped the engine after just two years. But the basic design and technology were resurrected for an iron block, a 198-cubic-inch V6.
How many miles will a GM 3800 last?
The GM 3800 was probably the best one. It was developed from the Buick 231 then 3.8, and proved so reliable GM used it in the rest of their makes except Chevy. It’s been known to go 3-400k miles if properly maintained. I’ve got 326,000 miles on my 05 grand prix, everything is original and still runs like a dream!
How can I make my 3.8 L V6 faster?
How to Get More Horsepower From a 3.8 V6
- Increase the amount of air flowing into the engine. Air mixes with fuel in each engine cylinder to produce combustion, which in turn increases horsepower.
- Increase the amount of fuel flowing into the engine.
- Increase the amount of air flowing out of the engine.
Who makes a 3.8 engine?
Chrysler 3.3 & 3.8 engine
| 3.3 & 3.8 engine | |
|---|---|
| Manufacturer | Chrysler Corporation (1989-1998) DaimlerChrysler AG (1998–2007) Chrysler LLC (2007–2009) Chrysler Group LLC (2009-2011) |
| Production | 1989-2011 |
| Layout | |
| Configuration | Naturally aspirated 60° V6 |
What cars had the 3800 series 3?
Here’s the full list:
- 1997-2003 Buick Regal.
- 2000-’03 Chevrolet Impala.
- 1998-’99 Chevrolet Lumina.
- 1998-2003 Chevrolet Monte Carlo.
- 1998-’99 Oldsmobile Intrigue.
- 1997-2003 Pontiac Grand Prix.
What kind of engine does a 1975 Buick LeSabre have?
The bore was enlarged to 3.8 in (97 mm), identical to the Buick 350 and Olds 307 V8s, yielding 231 cu in (3.8 L) displacement. 78,349 231s were installed in Buicks for 1975. Due to difficulties with the new fuel economy and emissions standards, the engine produced just 110 hp (82 kW). This engine was used in the following vehicles: LD5
What kind of bell housing does a Buick 3800 V6 have?
Buick V6 engine. Though the pre-3800 rear-wheel drive (RWD) V6 uses the Buick, Oldsmobile, Pontiac (BOP) bellhousing pattern, an oddity of both the front-wheel drive (FWD) and RWD 3800 V6 is that although it is a 90° V6, it uses the GM 60° V6 bell housing (Metric Pattern). For use in the FWD applications,…
What is the bore and stroke of a Buick Special?
In initial form, it had a bore and stroke of 3.625 in × 3.1875 in (92.08 mm × 80.96 mm), for an overall displacement of 198 cu in (3.2 L). It weighed about 35 lb (16 kg) more than the aluminum engine, but was far cheaper to produce. Dubbed the Fireball V6, it became the standard engine in the 1962 Buick Special.
What kind of engine does a 1962 Buick Special have?
Dubbed the Fireball V6, it became the standard engine in the 1962 Buick Special. In their test that year, Road & Track was impressed with Buick’s “practical” new V6, saying it “sounds and performs exactly like the aluminum V8 in most respects.”.
