How much does a grease trap cost?
How much does a grease trap cost?
Q: What will a grease trap cost my business? A: The average install for a small grease trap (0-100 gallons) is between $250 and $1500. The average cost for the installation of a new grease trap (750-1500) is between $4,000 and $8,500. Grease recovery devices cost between $3,500 and $6,000.
How much does a 1500 gallon grease interceptor cost?
The average cost for the installation of a new grease trap (750 to 1500 gallons) is between $4000 and $8500.
How big should my grease trap be?
The overall size of the trap is determined by the number of gallons of water flowing down your drains, which is your rate of incoming flow. You’ll also want to make sure your grease trap’s rated capacity is twice your flow rate. For instance, the rated capacity of a 20 gallon per minute (GPM) grease trap is 40 pounds.
How much does it cost to empty a grease trap?
Most indoor grease traps with easy access are 30-200 gallons, and most pumpers will charge between $125-$180 to pump out these types of traps, provided the service is set up on an ongoing basis. Most pumpers would charge $190-$240 to just do a “one-off” pumping.
How much does it cost to install a small grease trap?
On average, a small grease trap installation costs between $250 and $1500. Grease trap replacement costs may seem expensive at first, but that’s nothing in comparison to how much money you’ll need to shell out if you need to replace it. Having a functioning grease-catching solution pays off in the long run.
How much does a 1500 gallon grease trap weigh?
Bottom to Center of Outlet 50″ Top to Center of Inlet 14″ Top to Center of Outlet 16″ Weight 2800 Lbs.
How many gallons is my grease trap?
Measure the height of the tank. Square the radius by multiplying the radius times itself. Multiply the answer from step three by π or 3.1415, then multiply that product by the height in order to find the cubic volume. Divide the cubic volume in inches by 231 in order to find the number of gallons.
How long does it take to install a grease trap?
The average installation time will vary. However, one can normally expect less than two hours from start to finish.
Do plumbers install grease traps?
Installations & Replacements for Grease Traps Our commercial plumbers can replace your grease trap or install one in your commercial kitchen to protect our plumbing. We’re experienced and helpful.
What are the dimensions of a 1500 gallon grease trap?
1500 Gallon Holding Capacity w Two 6″ Tall Manways. Inlet 4″ Width Front to Back 60″ Length Side to Side 120″
What are grease interceptors and grease traps?
Jensen Precast carries a large line of Grease Interceptors available for commercial applications. Also referred to as grease traps or grease recovery devices, our grease interceptors are designed for storage of greases/oils as well as solids before entering a wastewater disposal system.
What kind of grease trap do I need for my truck?
These all-welded steel Gravity Grease Interceptors are manufactured by Rockford Separators and can be installed above grade or flush with grade. Each is equipped with a removable 3/8″ nonskid diamond tread plate cover for flush-Grade Installation. The large capacity grease trap units come standard with heavy truck traffic load rating (H-20).
What is the H-20 load rating for grease traps?
The large capacity grease trap units come standard with heavy truck traffic load rating (H-20). Each closes with a heavy-duty gasket that prevents leaks and is covered with Bituminous coating to inhibit corrosion. Don’t see a grease trap that fits your needs?
What is the capacity of a grease extender?
Select the one that best fits your needs from 150 gallons up to 1,500 gallons holding capacity and from 800 to 7,560 pounds grease capacity. Each model is equipped with 4″ Threaded inlet/outlet for easy installation.
