How do I reset my Roomba 550?
How do I reset my Roomba 550?
Reset the Roomba battery 500 and 600 series
- Turn on your Roomba by pressing the button “Clean”
- Keep pressed during 10 seconds the buttons “Spot” and “Dock” that are placed above and under the button “Clean”
- Release the buttons at the same time and you will hear the typical sound of beginning of the Roomba.
What does err 5 mean on my Roomba?
Charging Error 5 means your robot’s charging system isn’t working correctly. If found, use a clean dry cloth to remove debris from the charging contacts. 4. Reinstall the battery and replace the bottom cover and battery door, and then place Roomba back on the Home Base® to try charging again.
Why does my Roomba keep saying error?
Overview. Error one (1) means your robot is on an obstacle or an uneven surface and a side wheel is stuck. If this is the case, lift your robot off the floor, place it in the center of the room, and restart the clean cycle. If this error occurred on a flat surface, check the wheels for obstructions.
How do I reset my Roomba error?
Press and hold HOME and SPOT Clean buttons on your robot for 10 seconds. When the button is released, Roomba will play the reboot tone. Wi-Fi connected Roomba 800 series. The reboot procedure is the same for Roomba 500 & 600 series, and also Wi-Fi connected Roomba 600 & 800 series.
How do I reset my Roomba 530?
Re: Can’t reset 530 Take the battery out, press and hold the Clean button for about 10 sec, reinsert the battery and charge for 3 hrs. See if after 3hrs the Roomba can reset.
How do I do a factory reset on my Roomba?
Roomba S, I, and 900 series Press and hold the Home, Spot Clean, and Clean buttons simultaneously. Then, wait for the light ring around the Clean button to begin swirling. Once there’s a light ring, let go of the three buttons. Now, the Roomba will restart, signaling the end of the factory reset process.
How do I reset my Roomba?
Roomba® i Series: Press and hold the CLEAN button on your robot for 20 seconds. When the button is released, the light ring will swirl clockwise in white. It may take up to a minute-and-a-half for your robot to turn on. The reboot procedure is complete when the light ring shuts off.
Why is my Roomba flashing orange?
The flashing orange light means it senses that the battery has been discharged and when docked it is recharging. Do not interrupt the cycle of charging the orange blinking light will cease and the unit should operate normally once charging is complete.
How do you reset a Roomba?
Press and hold HOME and SPOT Clean buttons on your robot for 10 seconds. When the button is released, Roomba will play the reboot tone.
Why does my Roomba 550 have charging error 5?
The charging err 5 is difficult to narrow down. Without a voltmeter you cannot verify the power supply is presenting the correct voltage to the Roomba. So at this point you could possibly have a defective PSU or a failed charging system component on the PCB or the battery is marginal/defective. Re: Charging Error 5, Roomba 550
What does charging error 3 mean on iRobot 500?
This error seems to be very common in the 500 series as well as the latermodels, especially if you swap the battery. Charging Error 3 When you hear 3 beeps or you get a Charging Error 3 on your iRobot App, the most probable culprit is the failure of FET test.
What does error code 10 mean on iRobot?
Select models will sound a two-tone “Uh-Oh” sound according to 10 beeps. iRobot defines error code 10 as referring to a condition where a side wheel is stuck or the bumper is not recognizing obstacles, but you can commonly treat it the way you treat code five errors.
What does error code 1 mean on Roomba?
The Error code number may be the most common problem, and probably because of this iRobot made it the first error. The Roomba narrates “Error one (1): Move Roomba to a new location then press CLEAN to start.” This usually occurs, due to the Roomba getting stuck or a side-wheel hanging or fails to touch the ground.
