How do you fix regeneration?

How do you fix regeneration?

Regen problems can be easily fixed… By far the best approach is to reduce the temperature at which the soot particles burn, by adding FTC Decarbonizer to the fuel at each fill. This reduces the soot burn temperature to 350-400C…a temperature readily reached by engines under even light loads.

What causes excessive Regen?

Your DPF regenerates because of excessive exhaust soot overwhelming the DPF. Exhaust soot is the product of incomplete combustion, the soot is actually partially burned fuel. There is only one answer to excessive DPF Regeneration: Eliminate or dramatically reduce diesel particulate matter (soot).

Why does my truck Regen so often?

A forced regen occurs when soot builds up inside the diesel particulate filter (DPF) to the point that the vehicle is no longer operable. When this happens, a driver has to pull over and initiate a self-cleaning process that can take up to 40 minutes — valuable time that could have been spent on the road.

Can you stop a parked regeneration?

To Cancel a Parked Regeneration hold the DPF Switch to the ON position for five (5) seconds and release. A Parked Regeneration will stop if the key is turned to the off position, the truck is put into gear or the parking brake is released. The regeneration will take approximately 20-40 min.

Why is my DPF not regenerating?

The DPF will not regenerate if: The engine management light is on for any fault; There is a faulty EGR valve; There is less than 20 litres of fuel in the fuel tank, if the fuel light is on or the engine management light is illuminated.

Does DPF remedy work?

DPF Remedy allows efficient fuel combustion at much lower ignition temperatures, resulting in less emissions AND up to 20% LESS FUEL burned. DPF Remedy can save you twice the cost of the product in fuel savings and are a great legal alternative to DPF delete.

How long should a parked regen last?

A parked regen is controlled by your truck’s computer system and only requires the correct conditions to be met. The process should last between 45 minutes to an hour and no longer. If your parked regen takes longer than this or isn’t finishing, something is wrong.

Can you drive while Regen?

Usually, nothing. The vehicle needs to run at operating temperature during the regeneration, so highway driving is best. Just drive as you normally would. During active regeneration, the exhaust outlet temperature is extremely high.

Why won’t my truck do a parked regen?

Clogged DPF filter – A clogged filter will not get to adequate temperatures to properly burn the soot off. Faulty temperature sensors – These readings will tell you how the DPF system is operating. If any sensor is faulty then it will stop the regen process.

What are the conditions for auto Regen to start?

If you’re working and the conditions are met for auto regen, it will start automatically and you can continue working as normal. To meet the conditions, the tractor must be warmed up and the engine RPMs above 1800. You must keep the RPMs up during the regen, which will last about 15 minutes.

What do you do when your Regen light comes on?

Parked regen is a more manual process that requires you to stop working. When the regen light comes on, here’s what you do: Park your tractor on a flat surface in a well-ventilated area. Keep the engine running in idle. Engage the brake. Put all shift levers in neutral. Turn off PTO. Warm up the engine.

How do you Regen a Chevy Silverado?

Put all shift levers in neutral. Turn off PTO. Warm up the engine. It should be running for at least 3 or 4 minutes before starting regen. Press and hold the regeneration button for a few seconds, until the regen warning light goes off and the regen process light starts to blink. Wait for the process to finish, about 30 to 40 minutes.

What is auto Regen mode on a tractor?

Some tractors are equipped with auto regen mode. If you’re working and the conditions are met for auto regen, it will start automatically and you can continue working as normal. To meet the conditions, the tractor must be warmed up and the engine RPMs above 1800. You must keep the RPMs up during the regen, which will last about 15 minutes.