How do you set up a Brocade FC switch?
How do you set up a Brocade FC switch?
Make an Ethernet connection and log in to the Brocade 16Gb FC Switch Module:
- Connect the workstation to the Ethernet network containing the HPE Synergy Frame Link Module.
- Connect to the switch using ssh or open a Telnet connection using the IP address set earlier.
- Enter the user name, using an administrative account.
How do I change the IP address on my Brocade 300 switch?
- Connect to the switch and log in using an account with admin permissions.
- Enter the ipAddrSet -ls command. • To add an IPv4 address, use the–add parameter. Specify the network information in dotted-decimal notation for the.
- Enter the ipaddrshow command to verify the result.
How do I change the speed on my Brocade SAN switch?
Steps
- Configure the port speed: portcfgspeed port octet_combo.
- If more than one ISL for each fabric is used, enable trunking by issuing the following command for each ISL port: portcfgtrunkport port-number 1.
- Enable QoS traffic by issuing the following command for each of the ISL ports: portcfgqos –enable port-number.
How do I set my Brocade switch to factory settings?
Tap the “Enter” key a few times and the Brocade command prompt will display. Type the console password if requested and press the “Enter” key. Type “configDefault” and press the “Enter” key. The switch configuration is now reset to factory default settings.
What is ISL in San switch?
An ISL is a connection between two switches through an Expansion Port (E_Port). When using ISL Trunking to aggregate bandwidth of up to four ports, the speed of the ISLs between switches in a fabric is quadrupled. For example, at 2 Gb/s speeds, trunking delivers ISL throughput of up to 8 Gb per second.
How do you change the IP address on a switch?
Select your network from the displayed list, and enter your password if prompted. Choose Change Settings then IP Address Settings. Go to Manual. Enter your IP address under IP Address and press OK to confirm.
Is it possible to assign IP address to be configured on a Layer 2 switch?
Contrary to Router/Firewall configuration, Layer 2 Switch has ports configured as Layer 2 which can’t be given an IP address, instead SVI (Switched Virtual Interface) needs to be assigned an IP address.
What is ISL in Brocade SAN switch?
Inter-Switch Links
For Brocade switches on which the Inter-Switch Links (ISL) are configured using FC ports, you must configure the switch ports on each switch fabric that connect the ISL. These ISL ports are also known as E-ports. All of the ISLs in an FC switch fabric must be configured with the same speed and distance.
How to set the Brocade FC switch values to factory defaults?
Setting the Brocade FC switch values to factory defaults You must set the switch to its factory defaults to ensure a successful configuration. You must also assign each switch a unique name. About this task In the examples in this procedure, the fabric consists of BrocadeSwitchA and BrocadeSwitchB.
Is the brocade 300 FC SAN switch still available?
Product availability: Models of the Brocade 300 FC SAN Switch described in this Product Guide are withdrawn and no longer available for ordering. The replacement product is Lenovo B300 FC SAN Switch. Changes in the June 2 update:
What is the brocade 300 ezswitch?
The Brocade 300 features the EZSwitchSetup wizard and can be configured in the Brocade Access Gateway mode of operation to simplify deployment. The switch provides full non-blocking performance with Ports On Demand scalability to support SAN expansion and enable long-term investment protection.
How many ports are available on the brocade 300?
The Brocade 300 comes standard with 8 licensed ports. The remaining unlicensed ports can be activated in 8-port increments by purchasing and installing the Brocade Ports on Demand (POD) software license packs. By default, ports 0 through 7 are enabled on the Brocade 300.
