How do you unlock the control lock on a Jenn Air dishwasher?

How do you unlock the control lock on a Jenn Air dishwasher?

Press and hold the designated control lock button for your model for 3 seconds. The location of the control lock button may vary depending on your model. Refer to the Owner’s Manual for the control lock button location for your model. The light will turn off and the control will be unlocked.

How do I turn off the control lock on my Jenn Air dishwasher?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds. If the dishwasher has a dedicated Control Lock button in the Options selections, press and hold CONTROL LOCK for 3 seconds (press the words “Control Lock).

Why is my dishwasher stuck on lock?

Release the control lock by pressing and holding the “Control Lock,” “Heated Dry” or “No Heat Dry” key pad for three seconds. The control lock light or icon should go out. Repeat the process to set the control lock again.

How do I turn off the lock on my Jenn Air stove?

After connecting the appliance to an electrical power supply or after a power failure, the control panel will be locked. An indicator light above the key icon will be on. To unlock the control panel, press and hold CONTROL LOCK for 3 seconds. The indicator light will turn off, and the appliance is ready for use.

What does red light on Jenn Air dishwasher mean?

Possible Solutions The red lock indicator shows that the control lock is activated, and the control panel cannot be used while this is activated. NOTE: You may need to disable Sleep Mode by pressing either Start/Resume or Cancel, or by opening and closing the door before you are able to turn Control Lock off.

Why won’t my dishwasher open all the way?

If the dishwasher is able to slide or move a little it could cause the door hinge to bottom against the edge of the cabinet trim and prevent the door from opening all the way. Check the both hinges and hinge springs while opening the door to see what’s stopping the door from opening all the way.

How do I get the Control Lock off my Whirlpool dishwasher?

Using the Control Lock on Your Whirlpool Dishwasher Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

How do I unlock my Jenn Air stove?

Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.

How do I Reset my Jenn Air dishwasher control panel?

Much like a computer, resetting your Jenn-Air dishwasher’s control panel can sometimes solve the issues you are experiencing. To reset the dishwasher control panel: Disconnect from the power source for one minute. After one minute reconnect the dishwasher to its power source.

Why is my Jenn-Air dishwasher not starting or operating?

There are several reasons why your Jenn-Air dishwasher not starting or not operating: dishwasher is in sleep mode delayed wash option is selected door is not completely closed and latched water supply is not turned on the power needs to be cycled to reset the dishwasher Is the control lock “on” or is the dishwasher in sleep mode?

What does the control lock light mean on a Whirlpool dishwasher?

The control lock is used to avoid unintended use of the dishwasher as well as to avoid unintended cycle or option changes during a cycle, some model have a sleep mode function. The control lock light will stay on for a short time, indicating that it is activated and all buttons are disabled.

How to troubleshoot Jenn Air JDB 5 jdb1100aws dishwasher?

Jenn Air JDB 5, JDB1100AWS dishwasher troubleshooting Problem Solution Dishwasher will not fill Dishwasher will not fill • Be sure door is latched securely. Dishwasher will not fill • Be sure the water is turned on. Dishwasher will not fill • Check that the pad is properly selecte