How fast do you push IV Dilaudid?
How fast do you push IV Dilaudid?
The initial starting dose is 0.2 to 1 mg every 2 to 3 hours. Intravenous administration should be given slowly, over at least 2 to 3 minutes, depending on the dose.
Can you give hydromorphone IV push?
DILAUDID INJECTION may be given intravenously, but the injection should be given very slowly. Rapid intravenous injection of opioid analgesics increases the possibility of side effects such as hypotension and respiratory depression.
Do you dilute IV push Dilaudid?
The safer way to administer through a running IV is to pause your pump, flush the line, administer your medication through the hub closest to the patient, flush at the prescribed rate of administration for the medication, then restart your pump. So, you see there is no need to dilute the drug.
What happens when you push IV meds too fast?
Too rapid administration of high doses (greater than 500 mg administered over less than 10 minutes) may precipitate hypotension, cardiac arrhythmia and sudden death.
How long do you push IV Zofran?
The recommended adult intravenous dosage of ZOFRAN is 4 mg undiluted administered intravenously in not less than 30 seconds, preferably over 2 to 5 minutes, immediately before induction of anesthesia, or postoperatively if the patient did not receive prophylactic antiemetics and experiences nausea and/or vomiting …
How do you do IV push medications?
Connect your medication syringe to the hub of your IV line using a “push and twist” motion. Disengage clamps, Slowly push the medication syringe to the speed noted in your medication orders. Once your medication syringe is empty, remove the syringe from the hub of your IV line. WASH HANDS.
What IV meds are slow push?
Table 1.
| Antibiotic | FDA-approved administration | IV push/IV slow injection |
|---|---|---|
| Administration | ||
| Chloramphenicol | IV push | Inject over at least 1 min |
| Penicillins | ||
| Ampicillin | IV push Slow IV injection IM | Inject over 3 to 5 min for 125-, 250-, and 500-mg doses Inject over 10 to 15 min for 1- and 2-g doses |
What IV push meds need to be diluted?
The following medications require dilution: ranitidine, famotidine, pantoprazole, lorazepam, promethazine. In certain settings, the following drugs require dilution in order to give them IV push: Digoxin Immune FAB, ephedrine, phentolamine, phenylephrine, phenytoin, vitamin K, magnesium sulfate.
How much Zofran can be given IV push?
What is the typical starting dose of Dilaudid?
The usual starting dose of DILAUDID INJECTION is 1 mg to 2 mg every 2 to 3 hours as necessary. Depending on the clinical situation, the initial starting dose may be lowered in patients who are opioid naïve.
What are the ingredients in Dilaudid?
HIGH POTENCY DILAUDID (DILAUDID-HP) is available in AMBER ampules or single dose vials for intravenous (IV), subcutaneous (SC), or intramuscular (IM) administration. Each 1 mL of sterile solution contains 10 mg hydromorphone hydrochloride with 0.2% sodium citrate and 0.2% citric acid solution.
What are the contraindications for Dilaudid injection?
DILAUDID INJECTION and DILAUDID-HP are contraindicated in patients with respiratory depression in the absence of resuscitative equipment and in patients with status asthmaticus. DILAUDID INJECTION and DILAUDID-HP are also contraindicated for use in obstetrical analgesia.
What is Dilaudid HP 10 mg used for?
DILAUDID-HP is indicated for the relief of moderate-to-severe pain in opioid-tolerant patients who require larger than usual doses of opioids to provide adequate pain relief. Because DILAUDID-HP contains 10 mg of hydromorphone hydrochloride per mL, a smaller injection volume can be used than with other parenteral opioid formulations.
