How many splines are on a 540 rpm PTO?

How many splines are on a 540 rpm PTO?

6 splines
In case of 540 rpm, the shaft has 6 splines, while for the 1000 rpm shaft, the number of splines is 21. If a PTO can run on both 540 rpm and 1000 rpm speeds then it is known as Dual PTO. This feature allows the operator to run the PTO at 540 rpm, but at a lower engine rpm than the standard, PTO rated speed.

What size is a standard PTO shaft?

Tractor PTO Shafts

PTO Type:	Type 1	Type 3
Diameter:	1 3/8″ (35mm)	1 3/4″ (45mm)
Speed:	540 RPM	1000 RPM
Gear teeth:	6	20
Rotation:	Clockwise, as viewed from end of shaft

Are there different PTO shaft sizes?

Regardless of what job you’ll be using a PTO shaft to complete, it’s important that you have the right size. There are two different speeds used most commonly with tractor PTO shafts, the 540 (type 1) and 1000 (type 3) RPM.

How far can you extend a PTO shaft?

The distance from the center of the drawbar hole to the end of the pto shaft should be no more than 20″ and no less than 14″.

What is a big 1000 PTO?

Sounds like your questions have pretty much been answered, but to summarize: The 540 pto shaft is a 6-spline shaft that is 1 3/8 inch in diameter. The small 1,000 rpm shaft has 21 splines and is also 1 3/8 inch in diameter. The large 1,000 rpm shaft has 20 splines and is 1 3/4 inch in diameter.

What is a 540 PTO shaft?

A 540 PTO (power take off) is the standard size PTO shaft on farm tractors. It runs the equipment pulled by the tractor and also many types of equipment that are stationary. Some that come to mind are , hay elevators, conveyors, pumps, generators, log splitters, ect.

Whats the difference between 540 and 1000 PTO?

On many implements where they offer both, the 1000 rpm drivelines are sized smaller, yet still transmit as much power as the 540 drivelines, because they are turning faster, and have more gear reduction at the implement gearbox.

What is a 540 or 1000 PTO?

1000-rpm PTO shaft on implements requiring less than 150 PTO hp, such as manure spreaders and rotary cutters. 540-rpm PTO shaft on implements requiring less than 75 PTO hp (light loads only), such as auger applications.

How long of a PTO shaft do I need?

To determine the length you need your PTO shaft to be, you need to measure the distance between the groove on your tractors PTO output shaft and the implements PTO output shaft.

What speed do Tractor PTO shafts come in?

The two speeds most commonly used with tractor PTO shafts is 540 and 1000 rpm and the PTO shafts can come in different sizes and lengths. Please consult with our experts online for any PTO shaft questions regarding PTO shaft parts, size charts, or extensions.

Where is This PTO shaft extender manufactured?

The PTO shaft should be attached to the extender with a shear bolt. Given the drawing size, the recommendation is to use a ¼” bolt. Where is this PTO extender manufactured? This product is manufactured in China. I do not have this information available to me please contact your tractor manufacturer. Does this piece match Kubota b6000dt?

What are PTO shafts & accessories?

PTO Shafts & Accessories Agri Supply stock a wide selection PTO shafts and yokes, clutches, shaft covers, tubes and any other accessories needed for your power take off needs. The power take off is used to transmit power from a tractor or other source of power to an implement.

What size roll/spring pin is required to attach the extender to PTO?

There is no adapter that is recommended for your unit. What size roll/spring pin is required to attach the extender to the existing pto shaft? The PTO shaft should be attached to the extender with a shear bolt. Given the drawing size, the recommendation is to use a ¼” bolt.