What is a Minute Man load?
What is a Minute Man load?
When implementing an aggressive fire attack, advancing hose is an important part of our job. One such load is the “Minuteman” hose load, which is designed to aid the firefighter in getting the initial attack line in place with ease for any type of operation, be it residential, commercial, or high-rise.
How do I load the modified Minuteman?
Loading the Modified Minuteman Load
- The hose is loaded in two single stacks and never crossed over itself.
- The nozzle and first 100 foot is always loaded to the left of the hose bed.
- The supply side with the bights is always loaded to the right of the hose bed.
What is one advantage of the Minuteman load?
One final advantage with the minute-man load is the ability to easily extend a line by shouldering the nozzle bundle, disconnecting it from the supply bundle, then adding it to the end of your line for an additional 100-feet of attack line.
What is a Dutchman in the fire service?
Dutchman — A term used for a short fold placed in a hose when loading it into the bed. This fold prevents the coupling from turning in the hose bed.
What is a Cleveland load?
The Cleveland load (aka Metro load or Roundabout load) is handline load primarily used for high-rise applications from what I have found. Other applications would be when deploying a handline not pre-connected to the engine.
Which factor should be considered when selecting a Hoseline?
This flow is impacted by three factors: total flow of water, hose length and hose size. Keep these in mind when selecting hoselines that must be stretched over long distances. Smaller diameter hoses such as the 1½ and 1¾ hose should not exceed 300 feet due to friction loss.
Which hose lay is performed by two engine companies when hose must be laid in two different directions?
A split hose lay is performed by two engine companies in situations where hose must be laid in two different directions to establish a water supply. The attack engine drops the end of its supply hose at the corner of the street and performs a forward lay toward the fire.
How do you store a lay flat hose?
After the use of PVC Lay Flat Hose, it should be cleaned, lined with PVC Lay Flat Hose to hang and sun, and then stored in a cool and dry place. 2. If a small opening is found in the use of PVC Lay Flat Hose, wrap it well with PVC Lay Flat Hose and weave or glue it as soon as possible afterwards.
What is single jacket hose?
A single jacket fire hose has one woven polyester jacket glued to the outside of the rubber liner. A single jacket can protect the rubber liner only if the hose is being used for occasionally light use, a temporary job or on a non-abrasive surface such as grass. Single jacket hose can save cost in the right situation.
How do I load the Minuteman hose?
To load the Minuteman hose load, first determine if you want to load a 150- or 200-foot preconnect. For the 150-foot preconnect, you will need three sections of hose. For the 200-foot preconnect, you will need four sections of hose. The first section of hose will be loaded as you would normally for any flat load.
What is a Minuteman load?
Minuteman Load (Female coupling on top, Male coupling on bottom). 4) Hose loads are Split (Side by Side) or a Combination Load (One.The Minuteman Load One common variation of the flat load is the minuteman load.
How did Oshtemo compare the performance of cross-lay hose load deployment?
The Oshtemo (Michigan) Fire & Rescue Department compared the performance for its cross-lay hose load deployment with that of the Philly load. They produced the video as a pitch to personnel in the department to change how attack lines were loaded. If playback doesn’t begin shortly, try restarting your device.
How much hose do I need for a 200 foot preconnect?
If you are loading 200 feet of preconnect, then you will have 150 feet of hose on your shoulder. You will certainly want a double stack load for this. One firefighter can pull the Minuteman hose load and advance the line. It is designed to unload itself as you advance toward the fire.
