Which countries use BS 1363?

Which countries use BS 1363?

British standard plugs and sockets according to BS 1363 are introduced in the late 1940s. Used in the UK, Ireland, Cyprus, Malta and some countries in Africa and Asia.

What is Type B plug?

Type B electrical plug has two flat parallel pins and a round grounding (earth) pin. Earth pin is longer than the other two so that the device is grounded before the power is connected. American and Japanese plus are similar in design. Type B plugs are rated at 15 amps.

What is standard electric plug?

The most common electrical outlet in any home is a 110 volt. Sometimes you may hear 110 volt plugs referred to as 120 volt. Do not be confused by this; think of them as one and the same.

What AMP is a standard plug?

13 amp
Most of us will have our standard or table lamps wired into a normal 13 amp plug, with a 3 or 5 amp fuse to protect it, and plugged into a standard 13 amp socket.

What AMP is a standard plug UK?

13A
A common UK plug is generally fitted with a 3A or 13A fuse. Plugs for appliances rated up to about 700 watts should have a 3-amp fuse (coloured red).

Why do UK plugs have 3 pins?

Prong Design: Like standard U.S. grounded plugs, the U.K. wall plug has three prongs. The U.K. plug is designed so that the grounding prong is slightly longer than the prongs responsible for transferring current.

What are Type A and Type B plugs?

Type A plugs are generally polarised and can only be inserted one way because the two blades do not have the same width. The blade connected to neutral is 7.9 mm wide and the hot blade is 6.3 mm wide. This plug is rated at 15 A. Type A and B plugs have two flat prongs with (often, but not always) a hole near the tip.

Where are Type B plugs used?

Countries Using Type B Electric Plug All of the noted for Type A except Bangladesh, Bolivia, Cambodia, China, Dominican Republic, Korea, Liberia, Maldives, Peru, St. Vincent, Tahiti, Thailand, Vietnam, Yemen. Also found in Azores, Belize, Trinidad and Tobago.

Which prong on a plug is positive?

Because we use A/C current, prongs don’t have have a positive and negative. Instead, the two prongs have a ‘hot’ and ‘neutral’ side. The wider prong connects to the neutral wire and the smaller prong smaller prong is the hot side of the circuit.

Can I use a 20A outlet on a 15A circuit?

There is no problem with using a 20A switch on a 15A circuit, as the breaker will trip and protect the switch from over-current.

What amp is a standard plug UK?

What is a 16amp plug?

A 16A plug is designed to draw a maximum of 16 A from a compatible socket, after which it will start to heat or burn or if it has a fuse ,it will blow off. Now since you have connected it to a 6 A socket, the socket can only give out 6 A in a go, after which it will also do the same as the 16 A does after 16.

What does BS 1363 mean for plugs?

British Standard BS 1363 requires use of a three-wire grounded and fused plug for all connections to the power mains. Two-wire class II appliances are not earthed and often have a plastic grounding pin which only serves to open the shutters of the outlet.

What is the UK plug standard for sockets?

United Kingdom / Ireland Plugs and Sockets. BS 1363. 13A/230V/50Hz. The official plug standard in the United Kingdom since 1962 is the BS 1363 plug. (The previous plug standard was BS 546, still found in older buildings.) The BS 1363 plug is also used in Ireland, Hong Kong, Malaysia, and Singapore. British standard BS 1363 requires use

Does BS 1363 require sleeves on power pins?

BS 1363 requires that all power pins (the shorter pins) are partially insulated. However, earth pins must be solid brass, or, in the case of plugs intended solely for use with non-earthed devices, solid plastic. BS 1363 is quite specific, clause 12.16 states “Sleeves shall not be fitted to any earthing plug pin.”.

What is the British Standards Institution standard for fuses?

The British Standards Institution standard for fuses in general is BS 4265. Appliances tested and approved by British agencies can only use approved plugs, and these are tested by ASTA-BEAB to BS 1363. ASTA requires that their mark be molded into the plug.The plug is rated from 3–13A/250VAC, depending on the fuse.