Can you make planters from decking?

Can you make planters from decking?

Once you’ve got your individual pieces you can screw them together to create your planter frame. If you’ve got more than one tier of decking boards then you will need some wood screwed in each corner, to both tiers, to keep both tiers together.

How do you build a wooden decking planter?

DIY Wooden Planters From Decking

1. Step 1 – Get the Materials Ready. First, gather all the materials needed to make the wooden planters with decking.
2. Step 2 – Lay Down the Base. Start by laying down the base of your planter.
3. Step 3 – Create Holes.
4. Step 4 – Fasten the Boards.
5. Step 5 – Attach the Base.
6. Step 4 – Fill it With Soil.

Can you use decking boards for raised beds?

I laid the decking out along the floor and then laid the supporting timber over the top, where the decking planks would join together. I decided to secure the decking raised bed together from the back so that no screws would be showing on the finished side.

Can you use pressure treated wood for planter boxes?

Yes, the “new” pressure treated wood is safe for use for raised garden frames… with a few precautions! Up until 2003, the most common preservative used for pressure treated wood was chromated copper arsenate (CCA), a compound using arsenic as its primary rot protectant.

What do you line wooden planter boxes with?

Line the entire planter with a sheet of plastic, trimming it so that it reaches but does not go over the rim. Staple the plastic all the way around the rim. Using a screwdriver or sharp stick, poke through the drilled drainage holes to let excess water drain out of the plastic liner.

Does a planter box need a bottom?

Planter bottoms usually are slatted, with some type of semi-permeable cloth barrier which permits drainage. Raised beds, however, do not have bottoms; they are open to the ground, which offers the benefit of permitting plant roots to go further into the ground for available nutrients.

How to make a wooden planter box?

1) Gather Tools. Building a planter box from wood requires basic tools such as a saw, power drill and sander. You’ll also need screws, a screen and a paint brush. 2) Select Lumber. Selecting the right lumber for your DIY planter project is essential. You’ll want treated or untreated wood that resists rot, mold and will last under outdoor conditions. 3) Plan and Cut Planter. The size of your finished planter is up to you. Use wood boards that are 5 to 10 inches wide. 4) Assemble Planter. The DIY planter box will have to be sturdy enough to hold plants and wet soil. It’s important that you fasten the boards together properly and securely. 5) Sand & Add Drainage Screen. Sand any rough edges on your planter box. If you’re considering a bare, natural wood look, give the planter an overall sanding. 6) Paint or Stain Planter Box. Protecting your DIY planter from moisture, mildew spores and UV damage will keep it looking its best. 7) DIY Planter Tips. Place your new planter in place and adjust the angle so that the box gets the correct amount of sun.

How to build a window box planter?

The width of the windows determines the final length of the planter.

Use brackets to support the weight of the box and the dirt that will fill it.

Certain types of wood aren’t suitable for this project. Pine rots easily and oak turns black when wet,so they are not good choices.

After determining the full width of the planter,cut front and back boards to the appropriate length.

Mark lines with square and use a belt sander to bevel corners at a 45-degree angle — this will reduce splintering.

Cut a slot at the end of the two boards to adjoin sides and increase strength.

Cut scrap wood left over from cutting down width,and already 7″ high for end pieces. These pieces are cut to 7″ long.

Measure the bottom piece for snug fit. Cut to proper width and length. Apply a bead of glue inside the bottom edges of planter.

Drill drainage holes in bottom,spacing about 12 inches apart,beginning about 6 inches from each end.

After the box planter is assembled,cut brackets to support the weight of the planter,dirt and plants and secure to the home’s exterior.

Once the planter is completed,a finish can be chosen to protect the wood and add color if desired.

Position each bracket where needed to provide good support here there’s one at the middle and each end.

Add remaining brackets and place box atop the brackets. Add dirt and plants or potted plants as desired.

How do you build a flower box?

To construct the flower box,trim off the original support posts using a reciprocating saw.

Lay out three more cut 4 x 4’s to serve as support posts for the box (Image 1).

Add a flower shelf,called a false bottom,inside the box.

Complete the flower box by constructing a top cap consisting of four miter-cut 2″ x 6″ boards.